SARWAX 886 SARWAX 886 is a modified, solid wax soluble in aliphatic solvents. The product can be used alone or in combination with SARWAX 885 for obtain very strong pull-up effects on all kind of leathers. It should be heated at 50°C for roller coating applications. The product can be used alone or in combination with SARWAX 885 for obtain very strong pull-up effects on all kind of leathers. It should be heated at 50°C for roller coating applications. LT – E 8027 LT – E 8027 is an emulsion of selected waxes and specific modifiers for special finishing. LT – E 8027 is specially developed for fashionable finishing. Generally it is use for corrected and full grain finishing. It is recommended to use this product by roller-coat or 1-2 spray. LT – E 8103 LT – E 8103 is a specific modified, aqueous, synthetic wax emulsion with low viscosity. This product imparts medium gloss and high filling effect properties. LT – E 8103 is used for highly filling effect in base coat and to increase finishing application properties for the production of dark polishable coats. It provides the darkens after polishing and hot plating . LT – E 8107 LT – E 8107 is a specific modified, synthetic wax emulsion. LT – E 8107 is used as highly efficient agent in base coats to reduce the stickiness during the plating or embossing process. It gives a good filling effect and produces an improvement of the piling properties. LT – E 8108 LT – E 8108 is a soft wax emulsion, which imparts a smooth, slippery feel to the leather. It provides high gloss and polishability properties. LT – E 8108 is ideally suited to use in polishing base coats for all types of leather. LT – E 8108 can be used either alone or in combination with other feel modifiers for a very nice touch. Demanded polishability and gloss can be achived by adjusting the quantitiy of the product respectively. LT – E 8390 LT – E 8390 is a micro-fine, natural wax emulsion. LT – E 8390 is properly used in resin base coats to reduce the plating and piling stickiness. In polishing grounds LT – E 8390 increases the gloss and the re-polishability. SARWAX CT 8370 SARWAX CT 8370 is slightly cationic wax emulsion designed as filler for soft leathers. It imparts on the leather a silky and natural handle. SARWAX CT 8820 SARWAX CT 8820 is emulsion of cationic waxes. It gives a very natural, waxy feel and improves the filling and pressing properties. For obtain crack effects with cationic finishing it can be used in the top-coat formulation. SARWAX CT 8822 SARWAX CT 8822 is an emulsion of cationic waxes with low viscosity. It gives a very natural, waxy feel and improves the filling and pressing properties. SARWAX CT 8822 is especially developed to use for double face leathers, and cationic studies. Very nice effect will be gain due to its cationic properties, when it is use as first coat within 1:2 water ratio on crystal effected double – face leather. Imparts natural leather by using within combination of our other cationic products on oily studies. SAROIL 897 SAROIL 897 is a dispersion of specially selected oils, which can be soluble in solvents. It has been designed to produce pull-up effects on full as well as corrected grain leather. SAROIL 897 can either be applied alone, or combination with SARWAX 886 or SARWAW 885 to improve the requested pull-up and feel effects After application the leather is recommended to left overnight . LT – E 8301 LT – E 8301 is a water dilutable emulsion of selected natural oils. It has been designed for improve absorption uniformity of leather surface and producing pull-up effects on full as well as corrected grain leather This product gives a very good pull-up effect and increases the repolishability. With higher temperatures during press, more pull-up effect is obtained. LT – E 8301 can be used alone or ,in combination with suitable additives and binders. LT – E 8304 LT – E 8304 is a water dilutable solution of selected natural and synthetic oils. It has been designed for producing pull-up effects on buffed leathers and on full as well as corrected grain leather.Products provides very good repolishability. This product gives a very good pull-up effect and water drop resistance. LT – E 8304 can be applied etiher cold or hot, and better deep penetration can be achieved when it is applied hot. It is used by reverse roller coater system. Product can be used alone or in combination with suitable products in SarChem product range. LT - E 8642 LT-E 8642 is a water dilutable oil which has been specially formulated to provide leather with a soft, oily feel and to produce special "oil pull up" effects. It is used on the base coat applications of full and corrected grain leathers. It gives softness, covering and fullness properties to the leather. Due to its chemical characteristics, it improves the penetration on the leather. Because of its property of giving pull-up effect, it can be used for this purpose, as well. It is recommended to be used with SARPUR 300 in order to become fixed with the leather and to strengthen the fixing property on other coats. SAROIL CT 8381 SAROIL CT 8381 is water-dilutable, cationic oil emulsion, which is used in combination with other cationic additives for multiple purposes, especially to produce a silky and little oily handle. LT – EK 8402 LT – EK 8402 is water-dilutable, cationic oil emulsion, which is used to optimise the absorbency of full and corrected grain leathers. LT - EK 8402 exhibits pleasant smooth handle, plate-release properties and improves the elasticity of the grain. It can be used in aqueous finishes as a feel modifier, to have pleasant oily-waxy handle. SARFILL 803 SARFILL 803 is a blend of specially selected oil, wax and polymers with high viscosity, which imparts high filling effect on leathers and soft waxy film. It is recommended to use in base coats of buffed upholstery, soft, corrected grain nappa leathers and especially as an auxiliary component for damaged full grain leathers to improve filling effects, remaining the softness of the leathers with its well levelling property. SARFILL 803 provides excellent smoothing effect by plating in low pressure and at temperature 90 ° C. SARFILL 806 SARFILL 806 is an aqueous blend of specially selected additives and polymers with low viscosity, which imparts high filling effect on leathers and waxy handle. Product provides excellent filling characteristics without damaging the grain of the leather. SARFILL 806 avoids grey break on application. SARFILL 806 is recommended to use on upholstery, sheep, and nappa leathers and especially as a feel agent for aqueous lacquers in applications. SARFILL 813 SARFILL 813 is an aqueous emulsion of special selected fillers, oils and polymers. It is universally used in aqueous base coats for all types of leathers for get rapid covering and reduced tackiness without deforming the softness of leather. SARFILL 813 provides very nice grain flanks on dry-milled leathers. SARFILL 817 SARFILL 817 is an aqueous modified wax emulsion. The product forms a dull opaque film. SARFILL 817 is an appropriate product for dye colored pull-up effect by mixing with water and dye solutions within suitable ratio, after base coat. LT – E 8501 LT – E 8501 is a very special combination dispersion of selected additives and fillers of high viscosity. Product is specially designed to produce exciting filling effects on buffed upholstery and full grain upper leathers. It shows extremely good embossing properties and does not cut through at high temperature and pressure. LT – E 8501 is used for aqueous base coats and as well as on foam finishing applications to reduce stickiness when plating or pilling it remains the grain break natural. SARFILL STUKO M SARFILL STUKO M is a blend of filling agents and modified polyurethane dispersion, in form of whitish paste. Product is especially developed for covering the defects on surface of leathers by its excellent filling property not to be seen after finishing application. SARFILL STUKO M is generally used on defected-grain leathers (especially on upholstery leather). Is applying done by hand to fill and cover all deep scratches on leather surface. LT – E 8503 LT – E 8503 is a blend of inorganic filling agents and highly viscous polymer dispersion. It is specially designed for roller-coat applications and suitable for car and furniture upholstery, shoe upper leathers and splits. The product can be applied by reverse roller coater without dilution or in combination with other additives on corrected grain as well as on full grain leathers and has excellent buffing properties. SARFILL CT 8374 SARFILL CT 8374 is an aqueous, cationic emulsion with special additives, is used for cationic finishes on both first and base coat applications. It exhibits very good oily and silky touch. It is recommended to use either within the 1/1 ratio when it is applied alone or between 100-300 gr/lt on cationic mixtures. SARFILL CT 8376 SARFILL CT 8376 Aqueous, cationic emulsion of synthetic and natural binders with special additives. In base coats solutions it gives a good surface sealing and fullness, on full grain and buffed leathers it produces soft and natural touch. SARFILL CT 8378 SARFILL CT 8378 is the matted version of SARFILL CT 8376 . LT – E 866 LT – E 866 is an aqueous, cationic filling agent. It improves handle and filling properties as well as excellent light fastness. It is recommended to use on base coat and dye coat applications of sheep skin, garment, double-face and nappa leathers. LT – E 866 prevents and reduces stickness duing the plating and pilling. Product improves touch, light fastness and provides excellent filling. LT – EK 8600 LT - EK 8600 is an aqueous light cationic emulsion of special waxes and oils with special additives. Product can be soluble in hot water at 60 ° C. Although its chemical structure is light cationic, LT – EK 8600 can be compatible with other anionic products, by diluting first in hot water, then adding into anionic product mixture prepared previously. LT – EK 8600 imparts excellent oily and waxy touch, improves the water absorption and appearance of leather surface. LT – EK 8600 is recommended to use as a highly efficient agent in plate finishing generally and as well as in base coat applications for glazing process. SARPEN CT 8430 SARPEN CT 8430 increases the moisturizing, penetration and levelling of cationic formulations. It is compatible with all the cationic CT-range of SARCHEM. SARPEN CT 8430 provides better penetration of base coat, to leather. It can be use on all types of full grain and buffed leathers. SARLINK 867 SARLINK 867 is a water-dilutable crosslinking agent based on polyaziridine with low viscosity miscible organic solvent in water. It improves crosslinkable of the finishing mixtures due to its high physical properties such as easy dispersible without any need to diluting before. SARLINK 867 improves wet rub and wet flexometer resistance. SARLINK 867 is recommended to use in aqueous top coats for car upholstery with ratio of 10-12 % depends on amount of binders and 2 % for CAB lacquers quantity . LT – E 8950 LT – E 8950 is a general purpose thinner of selected and carefully balanced organic solvents, which is designed to obtain drop effect on special finishing applications. LT – E 8950 is generally use either on base coat or on crust leather for garment, bag, shoe-upper and all fancy type of leathers. It is recommended to use with appropriate products in SARACRYL product range, to obtain the demanded drop effect. LT – E 8961 LT – E 8961 increases the viscosity of aqueous polymer dispersions in the alkaline pH range. Small proportions suffice to increase the viscosity to such an extent that dispersion behaves as a pseudoplastic fluid. LT - E 8961 can be corporate in the form of alkaline solution or LT – E 8961 can also be added in the form in which it is supplied. LT – E 8962 LT – E 8962 is a blend of special polymers and surface-active materials with high viscosity. Product is provide increasing viscosity, as well as improves levelling of top coats and base coats. LT – E 8962 is mainly use to maintain thickening effect, also can be regulated depends on type of polymers. It is recommended to use on top and base coats, usage amount should be decided for each type of application. LT – E 8965 LT – E 8965 is a specific modified, aqueous, polysiloxan clear solution with low viscosity. This product provides excellent flow out of aqueous base and top coats. LT – E 8965 is used for maintain the required perfect flow out in all aqueous finishing coats applications. It can be applied by roller coater and spray base coats or top coats. Also LT – E 8965 improves adhesion property of each finishing coats, without disturbing any effect on its physical properties. LT – E 8975 LT – E 8975 is an aqueous concentrated fine particle sized, inorganic matting agent. LT – E 8975 is used for maintain the required matting degree in aqueous base coats finishing applications of upholstery and car upholstery leathers. LT – E 8975 improves light and heat fastness properties, touch, embossing behaviors without disturbing any effect on its physical properties. In addition to these properties, LT – E 8975 reduces cutting through of soft base coats in application and as well as stickiness when plating and pilling.